Skip to Content

How to Install Faux Shiplap – One Room Challenge Week Two

Our entry spent it’s weekend getting Chip & Joanna-fied aka the shiplap went up. After drooling over shiplap the past few years, I am so excited to finally have a little bit of our own.

While we would have loved to have been able to afford real shiplap, it just wasn’t in our budget. So we opted to use plywood instead for faux shiplap.

The only reason we were able to even complete the shiplap project was because of my parents. My Mom figured out all of the measurements and board sizes while my Dad was the project manager of the shiplap project. I was his not-so-handy sidekick.

My Mom took the kids out for the two days and my husband worked on other projects around the house while my Dad and I got to work. By Sunday night, the foyer had completely transformed.

 

How to Faux Shiplap – Our Method

To shiplap a few walls in our entry, it took six plywood boards. We decided to go with quarter inch plywood so that it would flow more seamlessly with the moldings.

In some Facebook groups I have read that people have had success asking their local hardware store to make the plywood cuts for them (some people were able to get this for free while others paid).

We decided that because of our unusual cuts we needed due to the awkward angles and shape of the walls, we would be better off cutting the wood ourselves. My Dad purchased a special tool called a Rip-Cut (which he luckily got on sale!) to rip the boards into planks. Here are the steps we used:

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

These are my Mom’s very detailed drawings and measurements. Notice how it says Laura on it? That’s because my parents are always helping on projects in our houses – she had to make sure this one wouldn’t get confused with my twin’s shiplapped space.

1. Measure the walls, twice.

Make sure to measure every bit of space you will be shiplapping. To determine the width of your boards, it’s best to take the height of your space and divide it evenly. It’s okay if the bottom board is a little bit smaller or bigger than the others, but you don’t want to have like 8 boards all the same size and then one board that is half the size of the others. It’s better to have 9 boards that are a little more evenly sized.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.2. Find the Studs on the walls and mark all of them.

We marked ours by placing a piece of  painters tape on the trim in-line with each stud. We used a stud finder to find the studs.

3. Decide if you’re going to try to make a seamless look or if you want to vary your plank lengths.

We decided to go for a seamless look because we would only have two small areas that would need to be patched in our project. When my parents completed my sister’s shiplap project, they chose to cut the boards in varying lengths to create a look similar to hardwood floors. Based on your decision, you’ll know the lengths to cut your boards.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

4. Get your planks pre-cut by a local hardware store, or cut them yourself using a tool such as the Kreig Rip-Cut.

Cut them to the plank height you determined based on number one.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.5. Cut the planks to the length needed (based on number one).

You may have to check your lengths as you go along for each board. Turns out my entry walls aren’t squared. This means that the boards had to be different lengths as we went down the wall. We had to measure and cut each one as we went.

6. Sand each board with 120 grit sandpaper. Wipe the boards off with a rag or towel so you don’t bring the saw dust into the house.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style. 7. Using a nailgun, nail the first board on the wall (start either at the top or the bottom).

Place a nail far left or far right into the stud at the top of the board. Then place a nail at the top of the board and bottom of the board at each stud.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

8. Hold your next board up on the wall. Place a spacer in between it and the previous board that is already nailed to the wall.

The spacer helps to give you an even space between each board (which creates the shiplap look). We used a square because it was 1/8 inch thick. You could also use tile spacers or nickles to space the boards.

9. Once you have your spacers in place and the board in place, nail the board to the wall again at the top and bottom of the board at each stud.

10. Repeat steps until you have all of your boards hung.

11. For boards that have odd cutouts (such as outlets or switches), I suggest using cardboard to make a template.

This is a trick my Dad uses that makes cutting odd shapes easier by drawing on cardboard to make a template. Once you cut your template, you can place it on the wall to make sure it’s correct. Then, transfer the template to the board and cut the board. This will prevent cutting and wasting boards by testing the cardboard template first. Here is an example below:

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style. How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style. How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.  How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

12. Once all of the shiplap is up, prepare to paint. Tape your walls and trim where needed to protect your unshiplapped walls.

How to faux shiplap. Learn how to faux shiplap an entry. See how a 1980's entry gets farmhouse style.

13. Prime your shiplap or use paint and primer in one (which is what I did). You will need 2-3 coats of paint to cover the shiplap.

I paint matched my other walls so that the shiplap would match. Some popular farmhouse white paint colors perfect for shiplap are:

The best white paint colors for shiplap. The perfect farmhouse white paint colors. #shiplap #DIY

 

Next Steps in the Entry Remodel

Over the next couple of weeks, I’ll finish painting the shiplap, start my entry piece remodel, work on the artwork, and look for decor for the entry piece. We already finished the light, which I will share about next week.

Want to see the rest of our challenge – check out these posts:

Need More Inspiration?

Don’t forget to check out the rest of the One Room Challenge Guest Participants and the Feature participants. (The One Room Challenge brings bloggers together twice a year to redo one room in six weeks).

 

Boscov's Back to School Shopping. Get all of your back to school clothing and accessory needs in one store. Find quality yet inexpensive clothing that fits your family's busy lifestyle. Preschool Back to School.

How to Install Faux Shiplap. Learn the easy and cheap way to put up shiplap. It doesn't have to be hard and it definitely doesn't have to be expensive. This was such an inexpensive farmhouse project. See how we put it in our 2-story foyer! #shiplap #farmhouse #fixerupper

 

 

 

 

 

Crystal

Wednesday 15th of December 2021

What type of 1/4 inch plywood did you use? I went on home depots site to order it for curbside pickup but there are tons to choose from. I cant wait to tackle my bathroom with shiplap. Thanks for you do!

Laura

Wednesday 15th of December 2021

Hi Crystal, it was regular 1/4 inch plywood (the most inexpensive option at the time) with one side smooth finish and the other not. It was not a composite. Depending on your budget, you could use any kind you'd like. We were just going for the most inexpensive option :)

Kendria

Thursday 9th of January 2020

Hi, I'm a newbie here but I heard about you through a podcast. I was wanting to know what size plywood did you use, I seen 1/3 or 1/4"? I saw everything in the details but that. Thanks in Advance!

Laura

Friday 10th of January 2020

Hi Kendria! I used 1/4 inch plywood! I'll have to edit my post to include that - you're right, I totally left it out.

You heard about me through a podcast?? That's exciting. Which one?? :) - Laura

DIY Barn Door - How to Build a DIY Door for Less than $100

Wednesday 2nd of May 2018

[…] two great tips my Dad has taught me. Working with my parents, you learn a lot of great house tips. His cardboard template was what people e-mailed me about the most during our last One Room […]

DIY Bathroom Remodel - From Pink to Farmhouse One Room Challenge

Thursday 5th of April 2018

[…] DIY bathroom remodel before selling. We’re already nervous about our future buyers loving the shiplap in our foyer so we thought it was best to keep it to one […]

How to Turn a Cork Board into a Chalkboard - One Room Challenge Week Five | Mom Envy

Wednesday 1st of November 2017

[…] the before here. Looking to install some shiplap but don’t want to spend a fortune? Check out week two for a budget-friendly faux shiplap tutorial. And here is week three for the cheapest light […]